Single-phase transformer calculator
Enter the kVA and the two voltages off the nameplate. You get the ratio and the full-load current on each side. Optionally, give an actual secondary load to see the primary current, or a primary turns count to see the secondary turns.
Transformateur idéal, pertes ignorées. Le dimensionnement des conducteurs et de la protection contre les surintensités de chaque côté relève de votre Code, pas de cet outil.
Garder ces résultats
Nous envoyons ce seul courriel par notre fournisseur de courriel et ne gardons pas votre adresse, à moins que vous cochiez la case.
Nous envoyons ce seul courriel par notre fournisseur de courriel et ne gardons pas votre adresse.
How it works
- a = Vp ÷ Vs= Np ÷ Ns
- I = kVA × 1,000 ÷ Veach side, single-phase
- Ip = Is ÷ acurrent goes the other way
Each turn of wire on the core picks up the same slice of voltage, so the voltage ratio is the turns ratio. Power in is (nearly) power out, so the current ratio is the same number upside down. The kVA rating is volts times amps the windings can carry without overheating; divide it by either side’s voltage and you have that side’s full-load current.
Worked examples
A 3 kVA control transformer, 480 V to 120 V
- Ratio: 480 ÷ 120 = 4 : 1, step-down.
- Full-load primary: 3,000 ÷ 480 = 6.25 A. Secondary: 3,000 ÷ 120 = 25 A.
- With only 10 A of load on the secondary, the primary carries 10 ÷ 4 = 2.5 A.
- If the primary has 400 turns, the secondary has 400 ÷ 4 = 100 turns.
A 25 kVA pole-top unit, 2,400 V to 240 V
- Ratio 10 : 1. Primary full load: 25,000 ÷ 2,400 = 10.4 A.
- Secondary full load across the 240 V: 25,000 ÷ 240 = 104.2 A.
- A small current on the high side, a large one on the low side — the same power.
Questions fréquentes
Is this the current I size the conductors and protection for?
It is the full-load current — the starting number. How big the conductors and the overcurrent protection on each side must be, and where the protection goes, are code rules with their own multipliers and conditions. Take this current to your code book (CSA C22.1 in Canada, the NEC in the US) and your journeyman.
Why does the low-voltage side carry more current?
Power in is about the same as power out. If the voltage goes down by four, the current has to go up by four to carry the same volt-amps. A step-down transformer is a current step-up.
Does it matter which side I call the primary?
The primary is the side you feed. Swap the two voltages and the calculator shows a step-up with the ratio written 1 : n. The full-load currents do not change — they belong to the windings, not to which one is fed.
Voir aussi
- Single-phase transformers — the lesson behind this tool.
- Transformer basics — how two coils with no wire between them move power.
- Power triangle calculator — why the plate says kVA.
- Single & three phase formula sheet
Vous voyez une erreur sur cette page? Signalez-la
Merci — votre signalement a été envoyé.
L’envoi n’a pas fonctionné. Veuillez réessayer plus tard.
Un petit mot sur les outils qui vous conviennent — par courriel, facultatif
Laissez votre courriel et cochez la case pour un petit mot, au plus toutes les deux semaines, sur les outils, exercices et schémas qui vont avec ce que vous étudiez — ici et sur bentright.com et fieldcalc.net. Une seule liste pour les trois, un clic pour la quitter, et rien n’est envoyé avant que vous confirmiez depuis votre boîte de réception.